Read time: 6 minutes

Are you going spraying or killing weeds?

Spray drift is of great concern for sensitive crops and environments, along with the fact that if the spray doesn’t hit the intended target, you do your dough and your weeds live.

Bill Gordon, spray application consultant with Nufarm Australia says the focus of spraying herbicide needs to be on doing the job right so the weeds receive the correct dose and die, and this includes reducing the air borne fraction to a bare minimum.

Bill Gordon, Nufarm spray application consultant says most growers are implementing best spray practice when it comes to boom height and nozzle selection but the temptation to spray at higher speeds and into the night can over-ride common sense at times.

“In many cases this means not spraying at night if the wind speed is too low,” he says. “Many product labels prohibit night spraying due mostly to the risk of spray drift. Our studies have shown that with a coarse spray quality drift may travel up to 300 to 400 metres during the day after any inversion has broken, but spraying at night can leave up to five times as much chemical in the air using the same products, nozzles and ground speed. This can result in spray drifting 10 to 20 kilometres or more at night, and this is unacceptable for other farmers, the community and the environment.”

Mr Gordon says most growers are implementing best spray practice when it comes to boom height and nozzle selection but the temptation to spray at higher speeds and into the night can over-ride common sense at times.

“The flip side of this is that it is becoming more evident that using Delta-T as the main determinant of safe day-time spraying conditions may not be the best approach,” he says. “What really matters most is the wind speed and whether the weeds are stressed or not.”

“If the weeds are not stressed on a hot day, due to ample soil moisture, then spraying at a higher Delta-T may still be effective and safe, with course droplets surviving quite well and not becoming air-borne.”

This can essentially increase the number of daytime hours available to growers to get the job done without spraying at night or early in the morning when the risk of spray drift is the highest.

“Getting onto paddocks as soon as possible after rain and using up the daytime hours to target priority paddocks will maximise weed control and minimise spray drift risk,” says Mr Gordon. “Spraying can continue into the evening in summer if the soil remains warm and the wind speed stays above 12 km/hr. If the wind drops off, then spraying should cease, usually by about 10 pm through to a few hours after sunrise.”

The bottom line is that it is very difficult to determine a safe night-time spraying conditions.

When environmental conditions are borderline in terms of wind turbulence, the safe spray window can be extended slightly through the use of coarser sprayer quality where the proportion of droplets less than 150 microns is 10 per cent or less, keeping drift to a minimum. The trade-off, however, is reduced efficacy when using very coarse droplet size, particularly when the target is small, vertical or hard to wet.

“When buying new nozzles, check them against the new standard, which shows spray quality with adjuvants rather than water only,” says Mr Gordon. “The GRDC has recently updated and published the 2017 Nozzle Selection Chart for growers to use as a reference. Using the correct nozzle and adjuvant combination can have a positive impact in reducing spray drift and maintaining efficacy.”

[A new factsheet provides advice to help growers meet the new 2,4-D application requirements]

“Reducing ground speed by just 5 km/hr can also make a big difference to spray coverage and efficacy of weed control, particularly if there is a high stubble load present,” he says. “Water sensitive paper, in combination with apps such as ‘SnapCard’, is a good way to test the coverage, penetration and spray pattern achieved under different conditions, such as different ground speeds.”

Mr Gordon’s rule of thumb for effective weed control when applying fully translocated products (e.g. glyphosate and Group I) is a minimum of 6–8 per cent coverage, while coverage of 10–12 per cent or more is required for contact herbicides. “Pre-emergent herbicides are the most difficult to judge due to the number of variables involved in their effective application, but as a rule of thumb I generally look for coverage of at least 15–20 per cent,” he says.

Getting onto paddocks as soon as possible after rain and using up the daytime hours to target priority paddocks will maximise weed control and minimise spray drift risk. Spraying can continue into the evening in summer if the soil remains warm and the wind speed stays above 12 km/hr. If the wind drops off, then spraying should cease, usually by about 10 pm through to a few hours after sunrise.

If you are going out killing weeds, you need to get everything right.

Bill Gordon’s 10 Tips for Reducing Spray Drift

  1. Choose all products in the tank mix carefully.
  2. Understand the product mode of action and coverage requirements.
  3. Select (and check) the coarsest spray quality that will provide effective control.
  4. Expect that surface temperature inversions will form as sunset approaches and will likely persist overnight and even beyond sunrise on many occasions. DO NOT SPRAY.
  5. Use weather forecasts to inform your spray decisions.
  6. Only start spraying when the sun is about 20 degrees above the horizon and when the wind speed has been above 4–5 km/hr for more than 20–30 minutes, and clearly blowing away from any adjacent sensitive crops or areas.
  7. Set the boom height to achieve a double overlap of the spray patterns.
  8. Avoid higher spraying speeds.
  9. Leave buffers unsprayed if necessary and come back.
  10. Continue to monitor conditions, particularly wind speed, at the site during the spray operation.

https://www.weedsmart.org.au/webinars/spray-wisely-well-maximise-efficacy-bill-gordon/

Watch what happens in this demonstration of fine particle movement under surface temperature inversion conditions.

Other resources:

Related Articles

View all
Article
News

Never cut the herbicide application rate

Scientific studies have demonstrated that resistance can rapidly evolve in weeds subjected to low doses of herbicide. Some weeds can develop resistance within a few generations. Full rates when mixing herbicides too! When mixing herbicides it is important that each product is still applied at the full label rate to ensure high mortality. Applying different chemicals in one mix can provide an additive advantage. It is important to understand the mode of action of each herbicide on the plant when preparing a herbicide mix. This is just as important for pre-emergent grass weed mixes as it is for post-emergent mixes aimed at broadleaf weed control. ALWAYS READ THE LABEL. Surrounding weed seeds with a combination of pre-emergent herbicides with different modes of action can give a high level of control and help extend the useful life of all the chemicals used. The high level of control must be supported with additional control measures for all survivors. All products with different modes of action must be applied at full label rates for this to be an effective strategy.   Mixing two chemicals with the same mode of action can achieve some additional efficacy, however, the mix should deliver the combined full rate to ensure a lethal dose. The amount of stubble present and crop safety are all important considerations when mixing chemicals. For example, when using a tank mix of Avadex® and trifluralin to control ryegrass in wheat, the rates used will vary depending on the sowing system and level of stubble retention. Be sure to get good advice. Many herbicides on the market are a combination of two or more modes of action within the one product. These products must be applied at the full label rate to be effective. Having dual action does not negate the need to change herbicide products and rotate modes of action. Repeated use of any single strategy will reduce the effectiveness of that strategy over time.  
Article
News

Spray well – correct nozzles, adjuvants and water rates

Spray application is a technical field and growers need to make sure their equipment and application techniques are spot-on. The GRDC Spray Application GrowNote provides detailed information and about 80 videos to demonstrate key skills. Prevent spray-drift The focus of spraying herbicide needs to be on doing the job right so the weeds receive the correct dose and die, and this includes reducing the air borne fraction to a bare minimum. Bill Gordon’s 10 Tips for Reducing Spray Drift Choose all products in the tank mix carefully. Understand the product mode of action and coverage requirements. Select (and check) the coarsest spray quality that will provide effective control. Expect that surface temperature inversions will form as sunset approaches and will likely persist overnight and even beyond sunrise on many occasions. DO NOT SPRAY. Use weather forecasts to inform your spray decisions. Only start spraying when the sun is about 20 degrees above the horizon and when the wind speed has been above 4–5 km/hr for more than 20–30 minutes, and clearly blowing away from any adjacent sensitive crops or areas. Set the boom height to achieve a double overlap of the spray patterns. Avoid higher spraying speeds. Leave buffers unsprayed if necessary and come back. Continue to monitor conditions, particularly wind speed, at the site during the spray operation High water rates don’t have to slow you down Some growers are concerned that increasing the water rate when applying herbicide will slow down their spray operation and cost them money. However, the biggest financial loss during spraying usually comes from a failed spray job. To keep your spray operation as time efficient as possible when using more effective and reliable application volumes, you can: Use nurse tanks around the farm to reduce the time spent travelling back to a central re-fill point. Use a larger pump, e.g. 2.5 inch, to make re-filling quicker. Pre-mix the batch while the sprayer is operating. Many mixes can be held in the mixing tank for up to 6 hours. However, wettable granules and suspension concentrates will need agitation to keep them in solution. For pre-emergent herbicides in high stubble situations, carrier volume has a large effect on the level of control achieved. Across four trial sites Dr Borger’s research demonstrated that ryegrass control with trifluralin or Sakura® increased from 53% control when the carrier volume was 30 L/ha to 78% control when the carrier volume was increased to 150 L water/ha in high Water quality and mixing order Water quality is often overlooked as a possible contributor to herbicide failure and can lead to confusion over the herbicide resistance status of weeds on a property. Water should be considered as one of the chemicals in any mix, given that water quality varies markedly depending on its source. Getting the mixing order right is essential for effective spray results. Don’t start mixing until the water quality is right Podcast – Mixing herbicides Adjuvants Sometimes adding an adjuvant is beneficial and sometimes it is detrimental; and there is an art to knowing how to best deploy these additives. When weeds are susceptible to the applied herbicides, the effectiveness of adjuvants generally goes un-noticed. Correctly applied adjuvants can reduce the impact of low level herbicide resistance by helping to maximise the amount of herbicide taken up by the plant.
Article
News

Clean borders – avoid evolving resistance on the fence line

About one-quarter of glyphosate-resistant populations within broadacre cropping situations across Australia come from fencelines and other non-cropping areas of the farm. Along paddock borders, where there is no crop competition, weeds can flourish and, if not controlled, set lots of seed. The traditional approach has been to treat these weeds with glyphosate to keep borders clean but after 20-odd years this option is now failing and paddock borders are becoming a significant source of glyphosate-resistant weed seed. Weed researcher Eric Koetz said the limited options for managing weeds along irrigation infrastructure and other non-crop areas is a problem and is putting additional pressure on knock-down herbicides in irrigated systems. In some situations, cultivation can be used to kill the weeds and provide a firebreak, but on light soils this may pose an erosion risk and mowing or slashing may be safer options. Another possible tactic is to continue using herbicides but to ensure that a clean-up operation is carried out before any survivors can set seed. Some growers are choosing to increase the heat on weeds along the borders by planting the crop right to the fence and then baling the outside lap and spraying with a knockdown herbicide to kill any weeds and provide a firebreak. Another good option in some situations is to maintain a healthy border of vegetation using non-invasive grasses. In Queensland, buffel grass is a good example of a grass that can outcompete other weeds while not invading crop lands. If only herbicides are used on fencelines, resistance is inevitable. Surviving weeds on fencelines have no competition and access to plenty of soil moisture, so they set a lot of seed and resistance can easily flow into neighbouring paddocks. Other resources It’s time for a glyphosate intervention Farm hygiene cottons on – Cleave Rogan, St George What’s new in management of herbicide resistant weeds on fencelines? Keeping the farm clean – Graham Clapham, Norwin Don’t jeopardise glyphosate for clean fencelines Keeping fencelines clean Resistance risk to knock-down herbicides on irrigated cotton farms

Subscribe to the WeedSmart Newsletter